Measuring a COP ignition

Actuator information

Type: Coil on plug
Power supply: 12 V, from system relay
Signal type: Frequency varying
Signal level: -

Workings of a coil on plug ignition

With Coil On Plug (COP) ignition, each spark plug has its own ignition coil, directly mounted on the spark plug, without spark plug cables. Like in all ignitions systems, the coils transform a low voltage on the primary side to a high voltage on the secondary side to produce a spark across the contacts of the spark plug.

Three different COP ignition systems are available:

  • 2 wire COP ignition
    An ignition coil which is entirely controlled by ECU
  • 3 wire COP ignition
    An ignition coil with a controller module on it which is triggered by the ECU via the third wire
  • 4 wire COP ignition
    Same as the 3 wire COP but with extra control wire to ECU for feedback/diagnostic purposes

Each system requires a different measuring technique, but using the Coil-on-Plug probe TP-COP750, all systems can be measured with a single measurement setup.

Connecting the lab scope

With COP, no spark plug cables are present to clamp an ignition pickup on. To measure these signals, the Coil-on-Plug probe TP-COP750 can be used. The Coil-on-Plug probe TP-COP750 is connected to the lab scope using a Measure lead TP-C1812B and the lab scope is set to normal scope mode with the following input setting:

Channel Probe Voltage Range
1 Red probe COP probe 2 V
Black probe Leave unconnected

Measuring on a working COP ignition

Figure 1: Measuring on a working COP ignition

Simply place the probe on the coil, as can be seen in Figure 1 and the secondary ignition patterns become visible on your oscilloscope and can be analyzed.

Measuring

Figure 2 shows a waveform of a COP ignition of a car with idling engine. This signal can be downloaded and used to correctly set up the lab scope or as reference signal.

Download COP ignition measuremen

Lab scope measurement of COP ignition

Figure 2: Lab scope measurement of COP ignition

Channel 1 (red) in figure 2 shows the signal from a 4 wire COP ignition measured with the Coil-on-Plug probe TP-COP750. The signal shows the typical waveform of an ignition system. On the left side it starts with the module switching on the coil to build up a magnetic field. When ignition has to take place, the module switches off the coil and the magnetic field that is built up collapses and creates a high voltage in the secondary winding of the coil, this is the high spike in the signal. The high voltage creates a spark that sustains until the energy in the coil has become too low, which can be seen in the signal dropping.

Diagnosis

Signal values may differ on different types of engine control units and COP ignition. Consult ATIS for information on specific engine control units and COP ignitions.

The following signal deviations can indicate a problem:

  • No signal:
    Cause: position of the Coil-on-Plug probe TP-COP750 is not correct, no power supply to COP ignition, no trigger signal from ECU
  • Signal voltage too low:
    Cause: position of the Coil-on-Plug probe TP-COP750 is not correct, poor power supply to COP ignition
  • Noisy signal:
    Cause: GND wire of the measure lead is connected, leave this unconnected

RELATED ARTICLES

Honda Jazz holds back and stalls
A 2006 Honda Jazz with L13A i-DSI engine occasionally holds back and sometimes even stops. No error codes were stored in the car. Several components have been replaced or swapped with an other car. A lot was driven in the car with a scanner hooked up to monitor the "live data" to find an anomaly in sensor or actuator data. Nothing showed up. Only after diagnosing with a good automotive diagnostic oscilloscope, the cause of the problems was revealed.
Ford F150 with defective ignition coil
A Ford F150 has an ignition coil for each cylinder and one of them is defective. It is replaced by a new one, but that one breaks down within half an hour. It is replaced again, with the same result. Measuring with an automotive oscilloscope and a current clamp reveal that the ignition control module is defective.
Disclaimer

This document is subject to changes without notification. All rights reserved.

The information in this application note is carefully checked and is considered to be reliable, however TiePie engineering assumes no responsibility for any inaccuracies.

Safety warning:

  • Before measuring, check that sources of dangerously high voltages are switched off or shielded from contact. Voltages considered to be dangerous are voltages over 30 V AC RMS, 42 V AC peak or 60 V DC.
  • Keep a clean working environment when doing measurements.
  • This measurement and procedures are a examples / measuring suggestions and are no prescribed protocols.
  • TiePie engineering can not anticipate the safety actions that need to be taken to protect persons and appliances. Before starting a measurement, check which safety measures need to be applied.