Current clamp TP-CC80
The Current clamp TP-CC80 is a current clamp that will allow your oscilloscope to measure electrical currents up to 80 Ampère AC/DC, with a frequency response up to 20 kHz. When measuring with this current clamp, there is no need to break a closed circuit or to affect the isolation.
The long, narrow jaws allow performing measurements in narrow spaces.
For measuring DC current, a simple to operate zero adjust button is available.
To connect the Current clamp TP-CC80 to your oscilloscope, a BNC to banana measure lead is required, which must be ordered separately. For oscilloscopes with differential inputs, the Measure lead TP-C812B is recommended. For oscilloscopes with single-ended inputs the Measure lead TP-BNCI-100 is recommended.
Order code: TP-CC80
EAN: 7423635782715
Price: 108.90
Category: Current Clamps
The table below shows detailed specifications of the Current clamp TP-CC80.
Electrical | |
|---|---|
| Bandwidth | DC to 20 kHz (-3dB) |
| Effective measurement range | |
| 20 A range | output 100 mV/A, 1 V = 10 A |
| 80 A range | output 10 mV/A, 1 V = 100 A |
| Accuracy | |
| DC 20 A range | ±(3% ±5 mA) |
| DC 80 A range | ±(3% ±0.3A) (100 mA to 40 A) ±(8% ±0.3A) (40 A to 80 A) |
| AC 20 A range | ±(3% ±5 mA) (10 mA to 10 A, 40 Hz to 2 kHz) ±(4% ±30 mA) (10 mA to 10 A, 2 kHz to 10 kHz) ±(6% ±30 mA) (10 mA to 10 A, 10 kHz to 20 kHz) ±(8% ±30 mA) (10 A to 20 A, 40 Hz to 20 kHz) |
| AC 80 A range | ±(2% ±30 mA) (100 mA to 40 A, 40 Hz to 1 kHz) ±(4% ±30 mA) (100 mA to 40 A, 1 kHz to 3 kHz) ±(6% ±30 mA) (100 mA to 40 A, 3 kHz to 20 kHz) ±(8% ±0.3 A) (40 A to 80 A, 40 Hz to 20 kHz) |
| Output connection | cable with 2 shrouded 4 mm female banana sockets |
Dimensions | |
| Captured conductor size | 12.5 mm maximum |
| Weight | 210 g |
| Height | 38 mm (1.5 inch) |
| Length | 190 mm (7.5 inch) |
| Width | 70 mm (2.8 inch) |
| Length of cable | 30 cm (11.8 inch) |
Power Requirements | |
| Power indicator | Green LED |
| Auto power off | Yes |
| Battery type | Standard 9 V IEC 6F22 cell |
| Battery life | 80 hours typical with alkaline |
| Low battery indication | Red LED |
Ambient | |
| Operating Temperature | 0 to 50 °C |
| Relative Humidity | 25 to 70% |
| Storage Temperature | -20 to 70 °C |
| Relative Humidity | 25 to 80% |
Certifications and Compliances | |
| CE mark compliance | Yes |
| RoHS | Yes |
The Current clamp TP-CC80 is delivered with:
| Amount | Item |
|---|---|
| 1 | Carrying case |
| 1 | Current clamp TP-CC80 |
| Description | Version | Remarks | Size | |
|---|---|---|---|---|
| Current clamp TP-CC80 user manual | 1.3 | English | 305.46 kB | download |
RELATED ARTICLES
Direct injection servo hydraulic voltage and current
Lab scope measurement of servo hydraulic injector voltage and current on an idling engine at operating temperature. The measured voltage and current is shown and can be downloaded. To help determining whether the servo hydraulic injector is functioning correctly, different possible deviations from the example signal are mentioned along with possible causes.Read whole article...
Direct petrol-injection voltage and current
Lab scope measurement of direct petrol injector voltage and current on an idling engine at operating temperature. The signals from the direct petrol injector are shown and can be downloaded. To help determining whether the direct petrol injector is functioning correctly, different deviations from the example signal are mentioned along with possible causes.Read whole article...
Indirect injection current
With a lab scope an injector current is measured on an idling engine at operating temperature. The measured current is shown and can be downloaded. To help determining whether the injector is functioning correctly, different possible deviations from the example signal are mentioned along with possible causes.Read whole article...
