Automotive Diagnostics Kit ADK610004D
Motor management systems in cars get more and more sophisticated. When these sophisticated systems malfunction, sophisticated measuring equipment is required to locate the cause of the problem. With the TiePie engineering Automotive Diagnostics Kit ADK610004D, the automotive specialist obtains all necessary tools, an Automotive Test Scope ATS610004D-XMSG and special automotive accessories, to perform most of the diagnostic tests to locate the problem, all conveniently packed in a protective case.
The Automotive Diagnostics Kit ADK610004D contains a selection of TiePie automotive products neatly packed in a protective carry case. The main component of the Automotive Diagnostics Kit ADK610004D is the Automotive Test Scope ATS610004D-XMSG. The high sampling rate and large memory of the Automotive Test Scope ATS610004D-XMSG are very useful for capturing and analyzing longer fast signals such as CAN bus communications.
Several other products are included for diagnosing and solving common and less common automotive problems such as sensor malfunctions, actuator malfunctions, ignition problems, timing problems, power deficiency, etc. Refer to the automotive articles for examples of solved automotive problems.
The contents of this versatile Automotive Diagnostics Kit ADK610004D are:
|1||Automotive Test Scope ATS610004D-XMSG||1 GS/s four channel automotive oscilloscope with differential / single ended switchable inputs with SafeGround protection, SureConnect, resistance measuring, 250 MHz bandwidth, 14 bit resolution and 256 MS memory.|
|4||Measure lead TP-C1812B||3 m long, BNC to banana, low noise differential measure lead.|
|1||Back Probe TP-BP85 - Set of 8: Green, Blue, Yellow, Red, 4 Black||8 thin and flexible back probes, 1000 V CAT III with 4 mm banana socket.|
|2||Ignition Pickup TP-IP250||Capacitive secondary ignition pickup to be clamped on a spark plug wire.|
|1||Current clamp TP-CC80||80 A current clamp with 2% accuracy and 4 mm shrouded banana sockets.|
|1||Current clamp TP-CC600||600 A current clamp with 3% accuracy and 4 mm banana sockets.|
|1||Accelerometer TP-ACC20 - 09||Accelerometer with 2 axes, ±2 g range with 420 mV/g sensitivity.|
|4||Differential attenuator TP-DA10||Differential 1:10 attenuator, rated 300 V with 25 MHz bandwidth.|
|1||Alligator Clip TP-AC50B||5 alligator clips with 10 mm clamping range and 4 mm banana socket, rated for up to 60 V.|
|1||Carry case BB451||Carry case for all above mentioned items.|
Optionally, the Automotive Diagnostics Kit ADK610004D can be delivered with one of
|1||ATIS Lite||Automotive Test and Information System Lite is a comprehensive knowledge base with generic information to help the automotive technician diagnose car problems.|
|1||ATIS Pro||Automotive Test and Information System Pro is a comprehensive knowledge base with generic and brand specific information to help the automotive technician diagnose car problems.|
Go to the description tab for detailed information of each item in the Automotive Diagnostics Kit ADK610004D.
The Automotive Diagnostics Kit ADK610004D contains a selection of TiePie automotive products neatly packed in a protective carry case.
Heart of the Automotive Diagnostics Kit ADK610004D is the Automotive Test Scope ATS610004D-XMSG. This PC oscilloscope turns your computer into a sophisticated automotive diagnostic system. Equipped with four differential inputs, this automotive oscilloscope guarantees measuring multiple signals without the risk of creating short circuits through the oscilloscope. This compact automotive oscilloscope is USB powered, which makes it easy to connect it to a laptop computer and perform measurements while driving the vehicle. The large input range, the long memory buffers and high maximum sampling rate make it the possible to capture almost any automotive signal. The built in SureConnect connection test feature on each channel informs whether the test points have electrical connection to test subject, leaving no doubt whether there is no connection or no signal.
Automotive Test and Information System
The ATIS Automotive Test and Information System is a large knowledge base with information on almost all electrical and electronic components that are used in the motor management system of a car. In an intuitive graphical environment background information on sensors and actuators can be found, as well as detailed schematics, diagnosis instructions, component locations with photographs of most available cars and example signals for proper functioning components. The unique point of ATIS is the direct coupling between the diagnosis instructions with the example signals to the measuring instrument. One click of the mouse in ATIS will launch the automotive measurement software and load the specific settings to measure on the particular component. The mechanic can focus on finding the problem, he does not need to find out how to setup the instrument.
The Automotive Diagnostics Kit ADK610004D can be delivered with ATIS Lite or with ATIS Pro. ATIS Pro contains an extensive database with more schematics, connection diagrams and oscilloscope settings with reference signals.
To connect the Automotive Test Scope ATS610004D-XMSG to the automotive circuits, the Automotive Diagnostics Kit ADK610004D contains a set of four special measuring leads. The Measure lead TP-C1812B is a 3 meter long low noise BNC to 4 mm banana measuring lead, specifically designed to be used on differential oscilloscope inputs. The two ends of the Measure lead TP-C1812B with the banana plugs can be placed 2 meters apart, without picking up external disturbances. The length of 3 meter allows to connect the instrument to components under the hood while the instrument is located on the passenger seat, making it possible to perform measurement while driving. The measuring lead is made of silicone, making it heat resistant and oil resistant, perfectly suitable for automotive applications. The 4 mm banana plugs make it possible to connect a variety of test points or clamps.
To measure large currents, like e.g. starting currents, a Current clamp TP-CC600 is included in the Automotive Diagnostics Kit ADK610004D. The Current clamp TP-CC600 makes it possible to measure current with your automotive oscilloscope, without the need of breaking the circuit. Simply clamp the Current clamp TP-CC600 around the wire and measure the current, up to 600 A. Current measurements can reveal problems that with a voltage pattern remain hidden, like e.g. compression problems that are visible in the starting current.
Many components draw far less than 600 A, making the also in the Automotive Diagnostics Kit ADK610004D included 80 A Current clamp TP-CC80 a more suitable current clamp. It will measure up to 80 A, giving a much higher accuracy at low currents than the Current clamp TP-CC600. Use it to reveal problems in driving injectors, measuring leakage currents etc.
The Automotive Diagnostics Kit ADK610004D contains a set of Back Probe TP-BP85s. These thin and flexible measuring probes fit on any test lead with 4 mm banana plugs and make it possible to connect to hard to reach places. They allow to back probe wires in connectors, without breaking the circuit, without the need of break out boxes and without damaging the wire isolation. The set contains 8 probes, four black ones, a red, a yellow, a green and a blue one, matching the input channel color coding of the Automotive Test Scope ATS610004D-XMSG.
To safely measure the high voltage secondary ignition signals, the Ignition Pickup TP-IP250 is added to the Automotive Diagnostics Kit ADK610004D. Simply clamp the Ignition Pickup TP-IP250 around a spark plug cable and measure the secondary ignition signals, both from normal ignition systems and DIS ignition systems. Two pickups are included.
Accelerometer and manual trigger button
The Accelerometer TP-ACC20 - 09 is a dual axis accelerometer combined with a manual trigger button. It can be connected to the extension connector at the rear of the Automotive Test Scope ATS610004D-XMSG and two input channels.
The dual accelerometer measures accelerations up to 2 g in two planes. It can be used to measure vibrations in mechanical systems, but is can also be used to determine the maximum power of an engine, without the need of expensive equipment. Attach the acceleration sensor to the floor of the car and accelerate at full power. Using the weight of the car and the measured signal, the power can then be calculated by the software.
The manual trigger button can be used to trigger the automotive oscilloscope when the input signals are unknown. Connect the automotive oscilloscope to the sensors you want to check and start driving the car. As soon as the problem occurs, e.g. the engine holding back, press the manual trigger button. The automotive oscilloscope will now measure the signals and store them. Since the oscilloscope can store the signals before pressing the trigger button, later examination of the signals will show how the problem developed.
The manual trigger button can be used independently from the accelerometer.
The 80 V full scale input range of the Automotive Test Scope ATS610004D-XMSG and Automotive Test Scope ATS5004D makes it possible to measure almost any automotive signal. In case the voltage exceeds 80 V, the Differential attenuator TP-DA10 can be used to increase the input range of the automotive lab scope. This special differential attenuator attenuates the input signal by a factor 10. It can be used when measuring e.g. primary ignition signals or fuel injector signals. The Automotive Diagnostics Kit ADK610004D contains a Differential attenuator TP-DA10 for each channel of the lab scope.
In order to connect to various types of terminals where the Back Probe TP-BP85 cannot be used, the Alligator Clip TP-AC50B is included. Small enough to be used in narrow places, but enough clamping range to clamp on larger objects. Five clips are included in the Automotive Diagnostics Kit ADK610004D.
Convenient carry case
The Carry case BB451 is a convenient case for safely carrying your automotive tools. It offers dedicated storage locations for all parts of the Automotive Diagnostics Kit ADK610004D, like the Automotive Test Scope ATS610004D-XMSG and all accessories like measure leads, current clamps, test probes, ignition probes etc.
Several downloads for the Automotive Diagnostics Kit ADK610004D are listed below, including Multi Channel oscilloscope software, drivers and manuals.
Driver & Software
|WinUSB driver||10.0.2||Windows 10 / 11, 64 bit||1.73 MB||download|
|Multi Channel software||1.46.1||Windows 10 / 11, 64 bit, including PDF manual||100.56 MB||download|
Manuals & Documents
|Accelerometer TP-ACC20 user manual||1.3||English||875.29 kB||download|
|Automotive Test Scope ATS610004D-XMSG Instrument manual||2.43||English||953.50 kB||download|
|Brochure for Automotive Diagnostics Kit||English||1.72 MB||download|
|Current clamp TP-CC600 user manual||1.3||English||293.49 kB||download|
|Current clamp TP-CC80 user manual||1.3||English||305.46 kB||download|
|Differential attenuator TP-DA10 user manual||1.3||English||207.01 kB||download|
|Ignition Pickup TP-IP250 user manual||1.3||English||228.82 kB||download|
|Measure lead TP-C1812B user manual||1.4||English||453.24 kB||download|
|Multi Channel software manual||1.08||English||2.90 MB||download|